Wiring schema blogs

Useful to monitor audio power delivered to loudspeakers No power supply no setup required

This device, connected to the loudspeaker output of an audio amplifier, will indicate the instantaneous output power delivered to the loudspeaker(s) by means of six LEDs illuminating one after another by voltage values increasing little by little, providing the visual impression of a luminous bar or column, increasing and decreasing in height following the increase and decrease of the signals level.

The input signal is first rectified by D1 and then sent to six different voltage dividers, one for each LED. In this way, the indication provided by the LEDs illumination of this "Power Display", will be related to the instantaneous power sunk by the whole loudspeaker cabinet.

Six output power levels are displayed by the LEDs in a 2W - 80W range (no setup required). Each nominal power level indication into 8 Ohms load is reached when the respective LED illuminates at full brightness.

Circuit Diagram:

Six-LED Bar Audio Power Indicator Circuit Diagram

Notes:

• The output power indicated by each LED must be doubled when 4 Ohms loads are driven.
• The circuit can be adapted to suit less powerful amplifiers by reducing the number of LEDs and related voltage dividers.
• LEDs of any dimension can be used, but rectangular shaped devices will be more suitable to be compacted in bars or columns.
• For a stereo amplifier, two identical circuits are required.

Source : www.redcircuits.com

High Quality, very simple design, No preamplifier required

This design is based on the 18 Watt Audio Amplifier, and was developed mainly to satisfy the requests of correspondents unable to locate the TLE2141C chip. It uses the widespread NE5532 Dual IC but, obviously, its power output will be comprised in the 9.5 - 11.5W range, as the supply rails cannot exceed ±18V. As amplifiers of this kind are frequently used to drive small loudspeaker cabinets, the bass frequency range is rather sacrificed. Therefore a bass-boost control was inserted in the feedback loop of the amplifier, in order to overcome this problem without quality losses. The bass lift curve can reach a maximum of +16.4dB @ 50Hz. In any case, even when the bass control is rotated fully counterclockwise, the amplifier frequency response shows a gentle raising curve: +0.8dB @ 400Hz, +4.7dB @ 100Hz and +6dB @ 50Hz (referred to 1KHz).

Circuit diagram :

 10W Bass Boost Amplifier Circuit Diagram

Parts:

P1_________________22K Log.Potentiometer (Dual-gang for stereo)
P2_________________100K Log.Potentiometer (Dual-gang for stereo)
R1_________________820R 1/4W Resistor
R2,R4,R8___________4K7 1/4W Resistors
R3_________________500R 1/2W Trimmer Cermet
R5_________________82K 1/4W Resistor
R6,R7______________47K 1/4W Resistors
R9_________________10R 1/2W Resistor
R10________________R22 4W Resistor (wirewound)
C1,C8______________470nF 63V Polyester Capacitor
C2,C5______________100µF 25V Electrolytic Capacitors
C3,C4______________470µF 25V Electrolytic Capacitors
C6_________________47pF 63V Ceramic or Polystyrene Capacitor
C7_________________10nF 63V Polyester Capacitor
C9_________________100nF 63V Polyester Capacitor
D1_________________1N4148 75V 150mA Diode
IC1_________________NE5532 Low noise Dual Op-amp
Q1_________________BC547B 45V 100mA NPN Transistor
Q2_________________BC557B 45V 100mA PNP Transistor
Q3_________________TIP42A 60V 6A PNP Transistor
Q4_________________TIP41A 60V 6A NPN Transistor
J1__________________RCA audio input socket

Power Supply :

 Power Supply Circuit Diagram

Power supply parts:

R11______________1K5 1/4W Resistor
C10,C11__________4700µF 25V Electrolytic Capacitors
D2_______________100V 4A Diode bridge
D3_______________5mm. Red LED
T1_______________220V Primary, 12 + 12V Secondary 24-30VA Mains transformer
PL1______________Male Mains plug
SW1______________SPST Mains switch

Notes:

• Can be directly connected to CD players, tuners and tape recorders.
• Schematic shows left channel only, but C3, C4, IC1 and the power supply are common to both channels.
• Numbers in parentheses show IC1 right channel pin connections.
• A log type for P2 will ensure a more linear regulation of bass-boost.
• Do not exceed 18 + 18V supply.
• Q3 and Q4 must be mounted on heatsink.
• D1 must be in thermal contact with Q1.
• Quiescent current (best measured with an Avo-meter in series with Q3 Emitter) is not critical.
• Set the volume control to the minimum and R3 to its minimum resistance.
• Power-on the circuit and adjust R3 to read a current drawing of about 20 to 25mA.
• Wait about 15 minutes, watch if the current is varying and readjust if necessary.
• A correct grounding is very important to eliminate hum and ground loops. Connect to the same point the ground sides of J1, P1, C2, C3 &C4. Connect C9 to the output ground.
• Then connect separately the input and output grounds to the power supply ground.

Technical data:

Output power:
10 Watt RMS into 8 Ohm (1KHz sinewave)
Sensitivity:
115 to 180mV input for 10W output (depending on P2 control position)
Frequency response:
See Comments above
Total harmonic distortion @ 1KHz:
0.1W 0.009% 1W 0.004% 10W 0.005%
Total harmonic distortion @ 100Hz:
0.1W 0.009% 1W 0.007% 10W 0.012%
Total harmonic distortion @ 10KHz:
0.1W 0.056% 1W 0.01% 10W 0.018%
Total harmonic distortion @ 100Hz and full boost:
1W 0.015% 10W 0.03%
Max. bass-boost referred to 1KHz:
400Hz = +5dB; 200Hz = +7.3dB; 100Hz = +12dB; 50Hz = +16.4dB; 30Hz = +13.3dB
Unconditionally stable on capacitive loads

Source :www.redcircuits.com